Orangatang Moronga 72.5mm Longboard Wielen

Orangatang Moronga 72.5mm - Longboard Wielen

Orangatang Moronga 72,5 mm wielen.

De Moronga heeft een center set en een symmetrische vorm voor volledige flexibiliteit bij het draaien van uw wielen om gelijkmatige slijtage te bevorderen.

Een smal 35 mm contactvlak balanceert het lange glijpotentieel van het wiel met een heldere en definitieve aansluiting. Met dezelfde grote en lichtgewicht kern als de Balut is de Moronga ontworpen met een radicaal ander lipprofiel.

In tegenstelling tot een zachte radius dwarsdoorsnede sport de Moronga een dikke lineaire en zeer licht scherpe lip die overgaat in de lagerzitting nadat deze de buitendiameter van de kern bereikt.

Dit garandeert een proportioneel consistente lipvorm gedurende de levensduur van het wiel dat voorspelbaar glijdt en een betrouwbaar tractieniveau biedt.

Bovendien gaan de stijve en vlezige lippen samen met de brede kern om vervorming te minimaliseren en te zorgen voor soepele, rustige glijbanen en uitstekende slijtage-eigenschappen. Het inkapselen van de hele kern in urethaan voegt een beetje gewicht toe.

De afweging is echter een steviger ondersteunde lip en verhoogde trillingsdemping voor een grotere rit en soepeler stillere drift. Ze komen in drie verschillende durometers (urethaanhardheid); 80a 83a en 86a.

Hoe harder de durometer, hoe gemakkelijker het is om met lagere snelheden te glijden. Hoe lager de durometer, hoe beter controleerbaar uw dia's zijn bij hogere snelheden.

Specificaties:

Durometer:

  • 80a oranje: zacht en grijpend
  • 83a paars: harder sneller slidier
  • 86a geel: snel en glad
  • Diameter: 72,5 mm
  • Kernpositie: Center Set
  • Contactpatch: 55 mm

 

€ 62,95

Read on...

Product
 

81Custom Pegs 2Pack Step Pegs

81Custom - Pegs 2Pack - Step Pegs

2 in a set with a boltset:
This bolt set has 4 Screws and fits on every scooter.

Universal Pegs van 81Custom, past op bijna elke step.

Verschillende kleuren set van 2 stuks van dezelfde kleur

€ 19,95

Read on...

Product
 

BSB ABEC7 Bearings (16Pack) Skate Lagers

BSB ABEC 7 Bearings (16Pack) - Skate Lagers

Abec 7 lagers hebben de meest effectieve combinatie voor een zeer grote precisie gemaakt van hoogwaardige kwaliteit.

Lagers die minder slijtgevoelig zijn en zeer geschikt voor hogere snelheid.

  • Verpakt per 16 stuks
  • Maat 22mm buiten en 8mm binnen (608)

Abec 7's have the most effective combination of the tightest tolerances and high quality materials equipped with a single shield. Abec 5's are equipped with double stainless steel shields for contamination resistance. Abec 3's are equipped with double stainless steel shields and engineered for all skating style.

€ 34,95

Read on...

Product
 

Powerdyne Bearing Tool Onderhoud

Powerdyne - Bearing Tool - Onderhoud

Met deze bearing tool van Powerdyne is het verwijderen en plaatsen van je lagers in de wielen een makkie. 

A metal bearing tool designed to make installing and removing bearings in nylon-hub or no-hub wheels a cinch.

Because this tool works by slightly bending the hub of the wheel during installation and removal it is not recommended for use with metal or aluminum-hubbed wheels.

The PowerDyne Bearing Hand Tool is designed to make installing and removing bearings in nylon-hub and no-hub wheels a cinch. Because this metal tool works by slightly bending the hub of the wheel during installation and removal, it is not recommended for use with metal or aluminum hubbed wheels.

€ 15,50

Read on...

Product
 

Bones Cleaner Set Lager Schoonmaak Set

Bones Cleaner Kit - Onderhoud

Finally, a bearing cleaning unit brought to you by the bearing company by which all quality standards are measured.

  • Made of fluorinated high density polyethylene
  • 7 spacers for a good flush in less time
  • Cleans up to 8 bearings at a time
  • Cleans all skate bearings
  • Bearings and solvents not included

Instruction for the Bones Cleaner kit :

  1. Gently remove the non-contact rubber shield of the bearing by prying upwards from the center using a push-pin or by pressing it out from the back using a paper clip or pen knife. Do not clean the rubber shields with any solvent as this will cause the rubber to blister and ruin the fit on the bearing.
  2. Gently wipe them clean using a clean cloth or use soapy water. If you choose to use soapy water make sure to dry the shields completely before putting them back onto the bearing. We have tried many cleaners and solvents and have several recommendations. Citrus-based cleaners work but can leave a slight oily residue on the bearing. Solvents are more dangerous to use but often provide a more superior solution to cleaning dirty bearings. If you choose to use solvents we recommend wearing latex gloves and working in an area that is well ventilated. Solvents we recommend are Acetone Methyl Ethyl Ketone Citrus cleaner and Denatured alcohol. All of these can be found in the paint section of your local hardware store. Products we DO NOT recommend are petroleum-based products like; paint thinner gasoline kerosene lacquer thinner turpentine or anything that contains tolulene. These solvents aren’t adequate cleaners and should not be used in the bearing cleaning unit. Whatever you use make sure to dry your bearings and add the lubrication to them as soon as possible to keep them from rusting.
  3. Take your bearings and place them on the axle (metal rod on the lid) alternating from one bearing to one spacer till all 8 bearings are on the axle. For best results make sure that the ball side of the bearing is facing upwards. Fasten them down finger tight onto the axle using the wing nut.
  4. Fill the bearing-cleaning unit up about 1/3rd of the way full with your cleaning solution and seal the cap.
  5. Agitate the cleaning solution by shaking the bottle.
  6. Shake for about 30 seconds open the lid and give the bearings a spin to free up any debris and recap the bottle.
  7. Shake until you are satisfied that your bearings are cleaned completely. To make sure they are clean spin the bearings on the axle.
  8. Remove the bearings from the axle and dry with a clean lint free towel. We also recommend blowing the bearings out with a can of compressed air which you should be able to find at any electronics or office supply store. Be careful when doing this as you don’t want the solvent to get in your eyes or all over the place. Make sure to blow them out over a towel.
  9. Once the bearings are clean and dry the next step is to lubricate them. We have found through the years of testing that our Bones Speed Cream™ is the best light oil lubricant for your skate bearings. Put two drops of the lubricant per bearing and spin the bearing between your fingers to distribute the lubricant throughout the entire bearing. If you have ceramics only one drop of lubricant is needed.
  10. The next step is to put the rubber shields into position. They should just slip right into place with very little force.
  11. Occasionally you will see a wrinkle along the inner race edge. To get rid of this simply run your thumb over it lightly in a circular fashion.
  12. Now you’re ready to install the bearings back into the wheel. If you choose to use solvents please make sure to dispose of it properly. Most solvents will have disposal instructions on the container. Please be sure to be environmentally friendly and dispose of your cleaning agents in a responsible manner.

Bearings and solvents not included in package.

€ 19,95

Read on...

Product
 

Kickbike Cruise Max Matt Black Zwart Step Complete

Kickbike Cruise Max Matt Black / Zwart - Step Complete

De Cruise Max matt black is onze relax step, het ideale maatje op de boulevard. Je rechtop staande houding stept heerlijk ontspannen.

Surf the city! Kickbike’s cruiser catches the cruising spirit better than anything. You stand up. You wear beach shorts, smart suit, trench coat, anything. Cruiser glides and is just plain easy to ride. No need to avoid bumps and cobbles. You’ve got fat tires and perfect control of the ride. Cruiser is developed for riders who want an easy and elegant way to move around. Balloon tires give you a superb rolling and comfortable ride, no matter if it’s asphalt, cobbles or roadworks. Geometry is very relaxed and tuned for effortless cruising rather than fast kicking.


Cruise Max 20 is designed for:

  • riding to work, school & shops in style
  • relaxed touring
  • riding gravel roads and cobblestones

asphalt

gravel

excercise

easy cruising

g e n e r a l
Weight 9,9 kg
Included Frame mounted front mudguard, rear mudguard, reflectors, bell
small pump, tool set with 5 & 6mm allen keys, 8 & 10mm wrench, philips & flathead screwdriver
Optional accessories
f r a m e
Frame Kicbike Max, aluminium 2,8 kg
Footboard height 10,5 or 13 cm depending on the rear wheel position
Handlebar height 90 – 110 cm depending on the stem and handlebar position
Tested for rider weight 120kg
Recommended rider height 170-200cm
Color black, cream white, blue
w h e e l s
Tires Superfat cruiser tires. front: 60-559 (26 x 2,35″) / rear 50-355 (20 x 2,0″)
auto valves, recommended pressure 2-4 bars
Rims Double wall rims, aluminium, cnc-machined sidewalls
Hubs quick release hub with sealed ball bearings, front 36 spokes, rear 28 spokes
c o n t r o l s
Brakes V-brakes
Front Fork Aluminium, Integrated 1 1/8 aheadset bearings
Stem Aluminium, extension 100mm, angle +/- 15 deg.
Handlebar Aluminium, 50cm wide cruiser bar

€ 589,00

Read on...

Product
 

Zealous Built in Bearings Longboard Lagers

Zealous Built in Bearings - Longboard Lagers

De Zealous bearings zijn 1 van de betere kogellagers voor je longboard die er te koop zijn. Met de speciale groene rubberen afdichting komt er geen vocht en vuil in je lager en door het speciale nanokeramische vet dat gebruikt is, is deze lager zelfhelend.

De unieke eigenschap van dit vet is hoe de nanokeramische verbindingen kleine oneffenheden automatisch vult. Deze oneffenheden veroorzaken wrijving en hitte waardoor het glijmiddel op die plek uithard. Deze micro coating is 5x harder dan het metaal van de lager zelf en heeft een moluculaire verbinding met het metaal. Hierdoor blijft de rolweerstand minimaal en roest de lager aan de binnenkant bijna niet.

Specificaties

  • binnen diameter : 8 mm gaten
  • ingebouwde spacers
  • Set van 8 lagers
  • nanoceramisch vet

Zealous BearingsPrecision 8mm axle holes.409 built in spacers1mm built in speedringsGreen rubber seals to keep dirt and debris on the outside of the bearing.Lubed with Archoil Nanoceramic Grease-The unique feature of our lubricant is how the nanoceramic compound fills in deformations or asperities in the bearing. These deformations cause friction and heat around them which hardens the nano-ceramic compound to that specific area. This micro coating is 5 times the hardness of the host alloy and has a molecular bond with the host metal filling in all the asperities and eliminating friction over time.

  1. The coefficient of friction is the lowest in the field of Tribology at 0.003% creating a near frictionless surface. Mainly because the nanoceramic compound eliminates all asperities.
  2. Extremely low water washout
  3. Corrosion on the inside of the bearing is nearly eliminated.

Features:

  • Built-in Spacers
  • Built-in speedrings
  • precision 8mm Axle Holes
  • Tight tolerances for minimal play
  • Dual rubber seals keep bearings cleaner longer
  • Custom nanoceramic lubrication
  • Super Quiet
  • Set of 8 Bearings

€ 19,95

Read on...

Product
 
From 0 to 900 Euro

Dutch Dictionary

Search for glossary terms (regular expression allowed)